Item # ENV000C
ENVE SES Aero Road Handlebar $400.00
As part of the Enve Smart System (SES series), the new SES Aero Road Handlebar relies on Enve's most sophisticated technology and engineering techniques to ensure a fast, stiff, and aerodynamic set of drop bars. Similar to its Aero bar platform and carbon wheel lineup, Enve partnered with aerodynamics expert Simon Smart for this road bar project. An ex-formula One aerodynamicist with more than 15 years of experience in the motor sport world, Smart worked directly with Enve to create this new cockpit design.
To start, the Enve SES Aero Road Handlebar was designed specifically with racing in mind. As such, it's the first handlebar Enve's built with hidden, internal cable routing paired with a rigid carbon construction. Wearing much of the same profile as Enve's standard compact road bar design, the Aero was developed to work with a variety of hand shapes. The first thing you'll most likely notice is the super-flat, wide top section of the bars. The main objective here was to increase the bar's aerodynamics by creating this wind-cheating profile. This UCI-approved teardrop section smoothly flows into the 31.8mm clamping interface.
The bars feature 127mm of drop and 77mm of reach, along with 25mm of flare from the tops to the lowest section of the drops. The handlebar also incorporates a sophisticated pair of integrated bar ends. With its 100% handmade carbon fiber design, the SES Aero Road handlebar is exceptionally lightweight, rigid, and aerodynamic.
The Enve SES Aero Road Handlebar is available in three sizes from 40cm to 44cm and in the color Black. The bar weighs roughly 250g. Please note: Because the bar flares from the top down and is measured from center-to-center at the ends, the tops are narrower than the listed measurement. Enve recommends ordering a size up from normal if you spend the majority of your time riding on the hoods and tops.
- Carbon fiber
- Aerodynamic design
- Internal cable routing
- Bar ends flared wider than top width
- Width measured center-to-center at bar ends
- 31.8mm diameter at clamp
Actual weights are measured in-house by the Competitive Cyclist team.
Have questions? Chat with a Gearhead
Claimed weights are provided by the vendor.
Have questions? Chat with a Gearhead
View more Drop Handlebars
Reviews & Community
After mounting these in the stem is there...
After mounting these in the stem is there room for a K-edge garmin mount next to the stem before the bar flares out?
There should be enough room for the K-Edge , but that depends on the width of you stem.
I have this aero bar mated to the ENVE Stem. Granted, mine are both painted to match, so tolerances were slightly tighter, but there is little to NO room for most mounts.
I tried all Bar Fly's, the K-edge (too tight), and Garmin's mount; none worked. I finally squeezed a mount found on amazon labeled as "SRAM". It sits a bit far out, but does the job. Otherwise, attach to stem where I couldn't see it well. I will try again with a Bar Fly & a dremel to get a better fitting mount. Cheers, Jeff
I know Enve wants to maximize the airfoil section of the bar, but why they had to make the clamp width section SO narrow is beyond me. I am a big-time aero weenie sprinter and these bars would be perfect for me BUT I likely will have to go with the SL-70s because of the narrow clamp width and the inability to use mounts (what's the fun of racing if you can't GoPro and share with your buddies, right?)
Enve has their own computer mount now. http://enve.com/products/gear/computer-mount-cmptrmnt/
Short answer: NO. It sounds crazy, but I've owned these bars and it was impossible to put ANY bar mounted accessory.
Great Aero Bar
- Familiarity: I've used it several times
I installed this bar in my Scott Foil. Very light and stiff. The upper flat portion of the bar is very comfortable under my medium hands while climbing.
Vibration damping is excelent!!
Measure your stem first...
Clamp area is 48mm