Free Podium Mesh Base Layer With Louis Garneau Mondo Primo Jersey or Bibs »
Sale $119.95 $199.99 40% off

Item # SHI0670

Tell us your actual inseam

Note: Actual inseam is not the same as pant inseam.  How to measure

We recommend a size in this bike.

Your inseam: Edit More details

Our size calculator is a starting point for finding the right size for you. To get personal advice talk to one of our fit experts at 1.888.276.7130 or chat now

Select options
  • Select options
  • One Color, One Size ($119.95)
  • 100% Guaranteed Returns
  • Free Shipping on orders over $50

Item # SHI0670

A new look.

Unless you've been meditating in a cave for the past couple of years, you've most likely caught wind that Shimano created a carbon fiber Ultegra pedal. Yes, the PD-6700 carbon pedals were 60 grams lighter than their aluminum counterparts, and they were moving closer and closer to resembling a discounted Dura-Ace iteration. Needless to say, they were widely celebrated. For this reason, Shimano opted to utilize the 'if it ain't broke don't fix it' strategy for the new Ultegra PD-6800 SPD-SL Pedals.

Even while these come within 35 grams (per pair) of the Dura-Ace 9000 pedals, Shimano has ensured that the pedals still deliver the same blissful retention and instant release that we've grown accustomed to from SPD-SL pedals. In fact, the retention mechanism hasn't changed at all. The retention setting is still adjustable by wrench from the aft portion of the pedal.

As for the carbon pedal body, the 6800 design differs from 9000 through its use of short carbon fibers instead of Dura-Ace's long carbon fibers. Essentially, this is where the extra weight comes from. Additionally, the carbon has been molded with a machined aluminum sleeve that houses the two bearings in each pedal. The whole assembly spins on a stainless steel spindle, and the new pedals retain the replaceable stainless steel wear plate that sits atop the pedal body. Additionally, it supports the SPD-SL cleat for maximum lateral stability, while allowing a hard surface for your cleat to float against -- +/- three degrees.

The Shimano Ultegra PD-6800 SPD-SL Pedals come with a set of SM-SH11 floating cleats (the ones with the Yellow wear tabs) and all of the necessary mounting hardware. The float is three degrees in either direction. The stack height is 13.7mm. And as always, the retention preload is adjustable to allow you to dial in the perfect entry and release tension.

  • Carbon body
  • Aluminum cleat plate
  • SPD-SL cleat type
  • 3-degrees of +/- float
  • Adjustable entry/release

Tech Specs

Float:
+/- 3 deg
Actual Weight:
One Color, One Size: 260g
Pedal Wrench Type:
[Allen] 8 mm
Material:
[pedal body] carbon fiber, [cleat plate] aluminum
Entry / Release:
adjustable
Recommended Use:
road cycling and racing
Manufacturer Warranty:
2 years

Reviews & Community

What do you think of the

Shimano Ultegra PD-6800 SPD-SL Pedals

? Share a...

Write a review

No file chosen

Rather attach a photo from another website?

Rather attach a photo from your computer?

    Add a:
  • Share a photo
  • Share a video

Familiarity:

Only jpg, jpeg, png, gif or bmp files please.

Submit Cancel

Here's what others have to say...

5 5

best pedal on the market

  • Familiarity: I've put it through the wringer

This gets my endorsement of absolute best pedal on the market. I've put this thing through thick and thin and it always comes back for more. Love this pedal.

Unanswered Question

I thought the float comes from which cleats I have, Shimano's red vs yellow, not which pedals. If I match red cleats with these pedals, will the degree of float be different than if I used the Dura-Ace pedals? Thx.

5 5

Have these on 2 bikes

  • Familiarity: I've used it several times

So I have these pedals on both my wife's and my bike. The wife's pair is about two years old and mine just a couple weeks. Both have not disappointed and I really don't think twice about them. Clipping into the pedals seems very easy, but I'm also comparing it to my mountain bike pedals which seem a little more difficult. I also purchased a back of pair of cleats in the case the either of ours needs to be replaced. http://www.competitivecyclist.com/shimano-spd-sl-cleat-sets

5 5

Great Pedal

Clip in and out is super easy with adjustment to make it easier or harder. An 8mm Allen wrench is needed to install these pedals.

Great Pedal
5 5

Great Pedals!

  • Familiarity: I've used it several times

So, I finally, after about 8 years on the Look Keo Ti pedals, decided to try something new. These pedals are not only a value, but the the larger platform offers a lot of stability, and they are really well balanced (easy to get in an out after a stop...or at the start of a crit). In all, in terms of value and performance, these pedals are an awesome buy!

5 5

Shimano just keeps getting better!

  • Familiarity: I've put it through the wringer

I decided to replace my 105 pedals after 12,000 miles of trouble free service. I had planned to replace with the new carbon 105 but could not believe my good fortune-CC has the Ultegra's on sale for about fifteen bucks less that the 105's. So, instant decision to upgrade! Like most of Shimano components they spend the research and engineering funds on the Dura-Ace line the the benefits trickle down to Ultegra, 105, etc. These are as smooth as a Dura-Ace set I rode a couple of years ago-so why would you spend almost $80 more for the Dura-Ace-NO!-buy these and put the $80 toward new wheels where it would really make a difference. They are within 35 grams (1.2 ounces) of the Dura-Ace which is insignificant to most amateur cyclists. Buy these!!

Shimano just keeps getting better!
5 5

A great pedal!

  • Familiarity: I've used it several times

I had a pair of 6700s prior to the 6800s. I ditched the 6700s to try the Look Keo carbon blade. The Looks, look cool, have a great platform and clip out easily but clipping in is another issue. They don't point up when you're not clipped in which makes getting back in the pedal difficult.
So, I scrapped 'em in favor for the new carbon Ultegra pedal and am glad I did! Clip in and out is very easy, very stable platform, no hot spots and lightweight. What more can you ask for!

So the difference between the 6700 and...

So the difference between the 6700 and these is weight? The 6700 were aluminum and these have carbon? Is ride quality identical, the only difference being weight? Hopefully someone having used both can fill me in. Thanks.

Responded on

I've used both and they seem the same except for weight. Clip in, clip out is very smooth, bearings seem very smooth also.

5 5

A dramatic improvement over toe cages

  • Familiarity: I've used it once or twice and have initial impressions

I finally made the change to clipless pedals and I'm glad I did. The energy transfer is amazing, allowing me to go longer and more efficiently. I went straight for carbon figuring I could bring them with me should I ever upgrade my bike, so I can't comment on the differences between aluminum and other materials in comparison. Clipping in and out took a bit of practice and the tension needed some loosening for me to not feel glued to the bike, but I can see myself tightening it back up later as I become more experienced.

You'll need an 8 mm allen wrench to tighten these as opposed to a 15 mm pedal wrench. I hand tightened it with my Alien II multi tool because I don't have a torque wrench (the pedals suggest tightening to 10 Nm). Hopefully it's enough.

4 5

solid and light weight

  • Familiarity: I've put it through the wringer

great pedals for the money. nice and light weight, yet strong/rigid. can't feel any difference vs. my dura-ace pedals. solid purchase at the sale price, but may be able to find a little cheaper elsewhere.