Code: WINTER50—Spend $250, Save $50 »

Crank Brothers Egg Beater 11 Titanium Pedals

Out of Stock

Item # CRN0142

Don't worry though, we have a lot more Clipless Pedals in stock than that.

View Similar Products
Item # CRN0142


Eggbeaters are some of the easiest-to-use clipless pedal systems around. Thanks to the four-sided wing of the Eggbeater 11, it's literally impossible to not clip in with lightning quickness as soon as the bottom of your shoe hits the pedal. The Eggbeater wing rotates either forward or backward under the pressure of your foot to quickly and smoothly engage the cleat bolted to the sole of your shoe. In addition to being quick and easy, the Crankbrothers Eggbeater 11 Pedals are exquisitely light.

When it comes to mud, there isn't a better pedal on the market. Eggbeaters are made for slop. Their open design allows dirt, mud, and muck to pass right through as you engage your cleats. These Eggbeater 11 Pedals are the most recent iteration of the top-of-the-line Eggbeater 4Ti pedals. Similarly, they have titanium bodies, wings, and spindles. The spring is stainless steel for durability and consistent tension. And maybe the nicest thing is that no matter where you ride, stainless and titanium will never corrode.

The brass cleats for the Crankbrothers Eggbeater 11 Pedals are small so they recess flush with the tread on the bottom of your shoes for easy walking. They're also designed for two release angles -- 15° or 20°. The release angle depends on which cleat you bolt to which shoe. Crankbrothers recommends the 15° setting if you're new to clipless. Otherwise, the 20° configuration will give you greater mobility on the bike without the worry of an accidental release. Needle and cartridge bearings will keep the Eggbeater 11 Pedals spinning smoothly -- a great improvement from the old bushings. And when the time comes for an overhaul, keep in mind that nobody else's pedals are as easy to service as Crankbrothers' pedals are. Shims to protect your shoes are included as well as all the hardware you'll need for installation.

Please Note: Titanium spindles are not for everyone. Crankbrothers recommends a 200lb (90kg) rider weight limit for the Eggbeater 11 Pedals.

  • Titanium body, wing, and spindle
  • Stainless steel spring
  • Needle and cartridge bearings
  • 15- or 20-degree release
  • Brass cleats and shoe-sole shims included
  • 200lb rider weight limit

Tech Specs

6a14v titanium
Entry / Release:
15-20 deg
Recommended Use:
mountain, cyclocross
Manufacturer Warranty:
2 years

Reviews & Community


Write a review

    Add a:
  • Photos
  • Videos

No file chosen

Rather attach a photo from your computer?


Only jpg, jpeg, png, gif or bmp files please.

Submit ReviewCancel

Here's what others have to say...

Avg. ride time: 5h 44m per week
  • Average ride time is based on Strava activity over the last 3 months. Give your reviews credibility by connecting your account.


  • Familiarity:I've put it through the wringer

I like these pedals for XC racing as well as CX racing.

Things I like best:

1) Light weight

2) Just the right amount of float

3) So easy to engage and disengage

4) Engagement is certain

5) Easy maintenance keeps them going for years


- I change bearings and re-grease at the start of every season. Takes about 10 minutes and requires a $10 rebuild kit.

- For comfort, this pedal requires a very stiff, carbon sole.


Best pedals for XC and CX!

  • Familiarity:I've put it through the wringer

I switched over to Eggbeater pedals a few years ago and now I can't imagine riding anything else for cross-country riding. The key to riding Eggbeater pedals and reaping the benefits over their competitors (weight savings, effectiveness in mud, ease of clipping in...these points are covered in the description) is to seasonally rebuild your pedals and replace your cleats before they get too worn out. This is generally a good rule of thumb for any pedal but it's especially important for the Eggbeaters. If you take care of those things, you'll find the Eggbeaters will last and continue to perform well.

When setting up Eggbeater pedals with a set of shoes for the first time, there are a couple things you'll want to pay attention to for optimal performance. First, make sure you install your shoe shields underneath your cleat. These will protect your shoes from the pedal wings which, if not used, may lead to some unwanted slop in the shoe/cleat interface over time. Second, make sure there's some contact between the tread of your shoe and the pedal body when you're clipped in. If you shoes rocks side to side while clipped in, this indicates there's not enough tread/pedal body contact. If this is the case, you can use the Crank Brothers tread contact sleeves on the pedal body to eliminate any rocking. Once you've set up your pedals, you'll be good to go!

One more very important thing, you can easily use your Eggbeater pedals as a bottle opener. Enjoy!

Rebuild after one season? How many miles are riding in a season? I've had bearing go bad after 150 miles, then the pedal completely come off the spindle before 300 miles. That's maybe 2-4 weeks of riding.

Avg. ride time: 12h 10m per week
  • Average ride time is based on Strava activity over the last 3 months. Give your reviews credibility by connecting your account.

Great XC race pedal

    I ran XTRs previously, but switched to Eggbeater 11s this year. Coming from the Shimanos the engagement is vague and the float is a bit much, but now that I'm used to them I have no complaints. I don't baby my gear, so they've taken their fair share of rock strikes and seem to be more durable then my previous Eggbeaters, actually.

    Great XC race pedal

    The only pedals

    • Familiarity:I've put it through the wringer

    Ultra light and beautiful. I wont use anything else. I like the eggbeaters much better than the Candy's. I find that the platform gets in my way. I've races this pedal for cross and mtb for the past 4 years. Go get some!!!


    Burly but sticky

    • Familiarity:I've put it through the wringer

    Overall I like these pedals. I have used them on both my Mt. Bike and my cross bike. They come in fun colors and add to the overall steeze of your ride. With that being said, I find that I have to constantly adjust my pedals for easier release. I have had a few unfortunate incidents with mazaneeta bushes while I was fully clipped in. Regardless, I still use these pedals and would recommend them.


    High end pedal

      This is an expensive pedal for a very high-end XC bike. If you are building an ultra-light XC dream bike (like a near 20 lb hardtail) this is the way to go. You need a stiff carbon soled shoe to mate with this pedal as there is no "platform" on this pedal. I would stick with the Candy pedal if you are doing bigger drops or ledgier trails, or are close to 200 lbs.